Skip to content
Your Safety, Our Assessment - Absolutely Free! Sign-up for a FREE site assessment.
Your Safety, Our Assessment - Absolutely Free! Sign-up for a FREE site assessment.

Spill Deck, InLine - 5-Drum Model Part #2333

Original price $612.00 - Original price $612.00
Original price
$612.00 - $612.00
Current price $612.00

Frequently Asked Questions

No. Spilled liquids will more than likely cause the internal surfaces of the bladder to adhere to each other. We cannot guarantee the proper deployment of a reused bladder.

We recommend using a pump (UltraTech part# 2345 can be used) to remove any spilled contents from a sump or bladder. (Note: spillage should be pumped into an approved container).

The spill deck ramp (part# 1089) comes complete with two steel clips that quickly install on the end of the ramp. These clips hook onto the connecting spill deck and keep the ramp from moving or shifting during loading or unloading. NOTE: The ramp is not designed to be used with the P1 spill decks or the short side of the P2 spill decks.

Other than the spill deck, you’ll need one bulkhead fitting (part# 1073) and one t-strip (part# 1131) for every 26” of spill deck length that is connected. For example, if you’re connecting a 4-drum spill deck to another 4-drum spill deck you would need two bulkhead fittings and two t-strips. If, on the other hand, you were connecting a 1-drum spill deck to the short end of a 2-drum spill deck, you would only need one each of the bulkhead fitting and t-strip.

Yes. All that is required is a 1 9/16” hole saw (1 ½” will also work). On each side of the Ultra-Spill Decks are “dimpled” areas that indicate where holes are to be drilled. Center the hole saw on the area you need to be drilled and carefully cut the hole(s) for your bulkhead fittings. File or “flame” any rough or sharp edges prior to connecting.

Sidewall plugs (Part# 2221) can be used if you are no longer connecting a spill deck and therefore have a hole that needs to be plugged.

Yes, all grating surfaces on the spill decks are slip-resistant.

The spill deck can NOT be moved with a forklift or pallet jack. The design of the spill deck sidewalls sometimes leads users to think that it is forkliftable or able to be moved with a pallet jack. But what may appear to be forklift pockets are actually supports for the grating.

The t-strips lay across the point where two spill decks come together. By “bridging the gap” this piece diverts spills to either of the decks and keeps any spillage from getting between the units.

One for each 26” of spill deck that is being connected.

(Note: The answer to this question is based on one assumption: That the spill decks are being used with 55-gallon drums). All of the spill deck bladder systems meet EPA requirements. The inline spill deck systems meet EPA requirements. By themselves, the 1-drum, 2-drum and 4-drum spill decks do not meet EPA requirements. They must be connected to an UltraTech bladder or another Ultra-Spill Deck to increase the total sump capacity to 55 gallons minimum.

Ultra-Spill Deck Plus Models use a grating that is 52″L x 26″W x 4″H. All other spill decks use a grating that is 48″L x 24″W x 2.5″H.

The replacement bladder (Part# 6340) is what you would need to order. It is just the bladder and does not include the outer housing. The bladder attachment (Part# 2317) includes a bladder and the outside housing.

The bladder will roll out 65.5″ away from the deck and will be 66″ wide when completely unfurled.

The bladder(s) should be replaced for any of the following reasons: (1) It captures a spill (regardless of the size of the spill), (2) It deploys, rolls, or falls out of the bladder attachment housing. (3) It has sat unused for more than five years.

More Info / Downloads

There is No More Links for Downloads

Helps Comply with These Rules & Regulations

  • EPA Container Storage Regulation 40 CFR 264.175
  • ADA Accessibility Guidelines for Buildings and Facilities (ADAAG)